Zhone provides a host of products geared towards the needs of the service provider with legacy networks. Zhone provides extensive support for TDM (Time Division Multiplexing) networks and applications, including Intelligent channel banks with integrated cross-connect capabilities, T1/E1 and sub-rate DSU/CSUs, business class analog modems, network extenders and POTS splitters.

Go to IMACS Product Specification Lists

Go to  IMACS Product Parts Lists

  IMACS Products | FOR SEARCH WITHIN THIS LIST USE YOUR BROWSER SEARCH FUNCTION (CTL F)
 Part Number Product Description
  IMACS Power Supplies:
8901 AC Power Supply, 120/240VAC, CE Marked Main power supply for AC-powered IMACS units. 120/240VAC, 50-60Hz input provides +/-5V and +/-12V. Can be used with 8903 Power Converter to provide -48VDC from 120VAC only. Can be used with 8905 Power Converter to provide -48VDC from either 120VAC or 240VAC. A second 8901 may be installed for load sharing redundancy.
890220 DC Power Supply, -48VDC, CE Marked Main power supply for use with external -48VDC sources. Provides +/-5V and +/-12V. Includes low input voltage alarm at 42 volts or less. A second 890220 may be installed for load sharing/redundancy.
8903 Power Converter, 120VAC to -48VDC Used with 8901 for 120VAC, 50-60Hz input to supply -48VDC voltage. Optional redundancy of the 8903 is supported in the IMACS 800 and 900 chassis only. Cannot be used with 240VAC input voltage.
8905 Power Converter, 120/240VAC to -48VDC, 100W, CE Marked Used with 8901 with either 120VAC/240VAC, 50-60Hz input to supply -48VDC system voltage. Optional redundancy of the 8905 is supported in the IMACS 800 and 900 chassis only. Used only in 6-digit chassis. Consult GSS if using with negative ground.
890620 Ring Generator, -48VDC Used to supply ringing current for all FXS cards and for FXO cards in Manual Ring Down applications. Functionally equivalent to 8906 but with much improved operating efficiency, lower operating temperature and lower input current. Provides control of In-rush current during startup and hot insertion.
8907 Power Supply, -24VDC, CE Marked DC main power supply for use with external -24VDC sources. Provides +/-5V and +/-12V. A second 8907 may be installed for load sharing redundancy. Consult GSS if using with negative ground, or if +24V is required. Use of any plastic front panel cards or 4-digit chassis in a 24VDC environment is not supported.
  IMACS Chassis | FOR SEARCH WITHIN THIS LIST USE YOUR BROWSER SEARCH FUNCTION (CTL F)
891630 IMACS 600 Chassis, CE Marked Steel chassis, front loading, "V' steel card guides; with installation kit. Provides 2 CPU slots, 8 universal slots and 1 Interface slot. Universal slots can support up to 3 Server cards and up to 4 WAN cards. All universal slots that are not allocated to Servers or WANs can be used for Users cards. Accommodates 1 main power and 1 redundant main or 1 main power and 1 AC/DC converter and 1 ringing generator. AC and dual DC inputs. NEBS compliant.
891830 IMACS 800 Chassis, CE Marked Steel chassis, front and rear loading, new "V' steel card guides; with installation kit. Provides 2 CPU slots, 3 Server slots, 4 WAN slots, 1 Interface slot, 8 User slots. AC and dual DC inputs. Two slots for main power supplies, 5 separate slots for -48VDC converters or ringing generators. CPU, WAN, Server cards and power supplies load from front. User, Interface cards, ringing generators and voltage converters load from rear. NEBS compliant.
891930 IMACS 900 Chassis, CE Marked Steel chassis, top & bottom front loading, new "V' steel card guides; with installation kit. Provides 2 CPU slots, 3 Server slots, 4 WAN slots, 1 Interface slot, 8 User slots. Two slots on top for main power supplies, 2 slots on bottom for -48VDC converters (either two 8905 or two 8908) or ringing generators. AC and DC inputs. All system components load from front. When used with the 8908 power converter, or with an external -48VDC power supply, the 891930 chassis allows for the power requirements of having up to 7 BRI cards installed. NEBS Compliant.
  IMACS Interface Cards | FOR SEARCH WITHIN THIS LIST USE YOUR BROWSER SEARCH FUNCTION (CTL F)
892060 Interface card, 8 T1/E1 Ports, 2400bps Modem, 32K NVRAM, CE Marked Physical interfaces for up to 8 T1/E1 lines on single 50 pin AMP connector, integral V.22bis modem and port (RJ11). VT100 control port (RJ45), DB9 computer port for connection to network management system and nodal port (RJ48) provides 1 alarm output to external reporting device. Stainless steel faceplate with ejector. Can be used with all system releases up to and including v3.x.y.
892160 Interface card, T1/E1 Ports, No Modem, 32K NVRAM, CE Marked Physical interfaces for up to 8 T1/E1 lines on single 50 pin AMP connector, VT100 control port (RJ45), DB9 computer port for connection to network management system and node port (RJ48) provides 1 alarm output to external reporting device. Stainless steel faceplate with ejector. Can be used with all system releases up to and including v3.x.y.
892260 Interface card, 8 T1/E1 Ports, No Modem, External Sync (framed T1), 128K NVRAM, CE Marked Physical interfaces for up to 8 T1/E1 lines on a single 50 pin AMP connector, VT100 control port (RJ45), DB9 computer port (COM 1) for connection to network management system and RJ48 computer port (COM 2), RJ45 for external sync connection and node port (RJ48) provides 1 alarm output to external reporting device. Stainless steel faceplate with ejector. Requires v4.0.2 or higher or 5.x.y CPU firmware.
892360 Interface card, 8 T1/E1 Ports, 2400bps Modem, 128K NVRAM, CE Marked Physical interfaces for up to 8 T1/E1 lines on a single 50 pin AMP connector, V.22bis modem and port (RJ11), VT100 control port (RJ45), DB9 computer port for connection to network management system and node port (RJ48) provides 1 alarm output to external reporting device. Stainless steel faceplate with ejector. Requires v4.x.y or v5.x.y CPU firmware.
892460 Interface card, 8 T1/E1 Ports, No Modem, 128K NVRAM, CE Marked Physical interfaces for up to 8 T1/E1 lines on a single 50 pin AMP connector, no modem, VT100 control port (RJ45), DB9 computer port for connection to network management system and node port (RJ48) provides 1 alarm output to external reporting device. Stainless steel faceplate with ejector. Requires v4.x.y or v5.x.y CPU firmware.
892560 Interface card, 2 T1 Ports, No Modem, 32K NVRAM Two RJ48 and Bantam Jack connectors for T1 or balanced 120-Ohm E1 lines. VT100 control port (RJ45). No DB9 computer port. Stainless steel faceplate with ejector. Can be used with system releases up to and including v3.x.y.
892660 Interface card, 2 T1 Ports, 2400bps Modem, 32K NVRAM Two RJ48 and Bantam Jack connectors for T1 or balanced 120-Ohm E1 lines. VT100 control port (RJ45). V.22bis modem (RJ11), DB9 computer port for network management connections and node port (RJ48) provides 1 alarm output to external reporting device. Stainless steel faceplate with ejector. Can be used with system releases up to and including v3.x.y.
892760 Interface card, 2 E1 Ports, No Modem, 32K NVRAM, CE Marked Two pair BNC connectors for 75-Ohm unbalanced E1 lines, VT100 control port (RJ45), DB9 computer port for network management connections and node port (RJ48) provides 1 alarm output to external reporting device. Stainless steel faceplate with ejector. Can be used with system releases up to and including v3.x.y.
  IMACS CPU Cards | FOR SEARCH WITHIN THIS LIST USE YOUR BROWSER SEARCH FUNCTION (CTL F)
880060 CPU card, BCON Bus-Connect, Host 3.x.y., Non-Redundant, 2 T1/E1, CE Marked The 880060 is the base model CPU card, with stainless steel faceplate with ejector. Supports 1 WAN card for a total of up to 2 E1 to T1 WAN ports (on separate WAN card). Does not support cross connect module or redundant CPU operation. WAN card must be installed in slot W1. Can operate in termination or drop and insert mode. CPU card also houses voice signaling firmware (included) and optional SNMP and/or TR-08 management firmware (must be ordered separately). CPU Host firmware must be ordered separately. Can be used with system releases up to and including v3.x.y. Requires appropriate Interface card (892060, 892160, 892560, 892660 or 892760).
880160 CPU card, XCON Cross-Connect, Host 3.x.y., Redundant Cap., Up to 8 T1/E1, CE Marked The 880160, with stainless steel faceplate with ejector, supports complex applications requiring more than 2 WAN ports and the ability to cross-connect DS0s between WANs. Supports up to 4 WAN cards for a total of 8 T1 or E1 WAN ports and has a built-in cross-connect module. Two model 880160 CPUs can be installed for CPU redundancy. 1:N WAN redundancy is also supported. CPU card also houses signaling firmware (included) and optional SNMP and/or TR-08 management firmware (must be ordered separately). CPU Host firmware must be ordered separately. Can be used with system releases up to and including v3.x.y. Requires appropriate Interface card (892060, 892160, 892560, 892660 or 892760).
880360 CPU card, XCON Cross-Connect, Host 5.x.y., Redundant Cap., Up to 8 T1/E1, CE Marked The 880360, with stainless steel faceplate and ejector, supports complex applications requiring more than 2 WAN ports and the ability to cross-connect DS0s between WANs. Supports up to 4 WAN cards for a total of 8 T1 or E1 WAN ports and has a built-in cross-connect module. Two module 8803xx CPUs can be installed for CPU redundancy. 1:N WAN redundancy is also supported (with relevant WAN card options). CPU card also houses voice signaling and SNMP management firmware (included) and optional TR-08 firmware (60102) (must be ordered separately). Requires v5.x.y CPU firmware (must be ordered separately). Requires appropriate Interface card (892260, 892261, 892360 or 892460).
880460 CPU card, RCON Bus-Connect, Host 3.x.y., Redundant Cap., Up to 4 T1/E1, CE Marked The 880460 CPU, with stainless steel faceplate and ejector, supports 2 T1 or E1 WAN links in slot W1 with a redundant card (similarly configured) in slot W2. WAN ports in slot W1 may operate in drop and insert or terminate mode. The 880460 supports another 2 T1 or E1 WAN links in slot W3 with a redundant card (similarly configured) in slot W4. WAN ports in slot W3 can only operate in 'terminate' mode and can only be used to support 820260, 821360, 821560 or 821570 HSU card ports and 824160, 824660 and 8249 OCU-DP ports. CPU Host firmware must be ordered separately. Can be used with system release up to and including v3.x.y. Requires appropriate Interface card (892060, 892160, 892560, 892660 or 892760).
  IMACS CPU Firmware | FOR SEARCH WITHIN THIS LIST USE YOUR BROWSER SEARCH FUNCTION (CTL F)
60101 CPU Firmware, SNMP Management This host code must be ordered, in addition to CPU host version firmware, if SNMP and Telnet support is required for the management of local and remote IMACS units. Order in addition to CPU Firmware for all releases except for Host Version 5.x.y (TCP/IP/SNMP is an integral part of v5.x.y CPU Firmware).
60102 CPU Firmware, TR-08 This host code must be ordered, in addition to CPU host version firmware, if required to provide Subscription Loop Carrier (SLC96) facilities as outlined in Bellcore TR-TSY-000008 based signaling for Centrex or similar services. Requires Host v3.4.y or greater on CPU.
Note: Only the latest version of each major Host release is listed below, but all previous maintenance releases are still available.
60346 CPU Firmware, Host Version 3.4.6 Latest release supporting the 3.4 platform. Please refer to the Product Bulletin for more details. Requires 880060, 880160 or 880460 CPU, or older equivalent.
60364 CPU Firmware, Host Version 3.6.4 Latest release supporting the 3.6 platform. This release supports all voice cards and all data cards, except 821660, 822460, 822560 and 828060. Does not support Server cards except 887160 ADPCM. Please refer to the Product Bulletin for more details. Requires 880060, 880160 or 880460 CPU, or older equivalent.
60365 CPU Firmware, Host Version 3.6.5 Special release adding increased functionality to the 3.6 platform. In addition to supporting functionality of the 3.6 platform, supports 822460 and 822560 SRU cards. Does not support any Server cards except 887160 ADPCM. Please refer to the Product Bulletin for more details. Requires 880060, 880160 or 880460 CPU, or older equivalent. Note: Because of added new features, this is not a free upgrade from 3.6.x.
60374 CPU Firmware, Host Version 3.7.4 Latest release supporting the 3.7 platform. In addition to supporting the functionality of the 3.6 platform, this release also supports WAN card 801560, Voice card 811760, FXO caller ID, SP signaling with ESF mode, and enhanced SNMP features. Does not support any Server cards except 887160 ADPCM. Please refer to the Product Bulletin for more details. Requires 880060, 880160 or 880460 CPU, or older equivalent.
60381 CPU Firmware, Host Version 3.8.1 Latest release supporting the 3.8 platform. In addition to supporting the functionality of the 3.7 platform, this release also supports the P-phone station (812160) and office (813160) cards, PM-IOR Router (828060) and the enhanced HSU card (821660). Does not support any Server cards except 887160 ADPCM. Please refer to the Product Bulletin for more details. Requires 880060, 880160 or 880460 CPU, or older equivalent.
60393 CPU Firmware, Host Version 3.9.3 Latest release supporting the 3.9 platform. In addition to supporting the functionality of the 3.8 platform, this release also supports the 822460 and 822560 SRU cards. Does not support any Server cards except 887160 ADPCM. Please refer to the Product Bulletin for more details. Requires 880060, 880160 or 880460 CPU, or older equivalent.
60412 CPU Firmware, Host Version 4.1.2 Latest release supporting the 4.1 platform. Please refer to the Product Bulletin for more details. Requires 880260 CPU, or older equivalent.
60423 CPU Firmware, Host Version 4.2.3 Latest release supporting the 4.2 platform. Please refer to the Product Bulletin for more details. Requires 880260 CPU, or older equivalent.
60502 CPU Firmware, Host Version 5.0.2 Latest release supporting the 5.0 platform. This release supports the 880360 CPU card and has increased functionality over the 3.x and 4.x series. It supports all Server cards in existence at the time of this release. Please refer to the Product Bulletin for more details. Requires 880360 CPU and 892260, 892360 or 892460 Interface card.
60515 CPU Firmware, Host Version 5.1.5 Latest release supporting the 5.1 platform. In addition to supporting the functionality of the 5.0 platform, this release also supports the 802060 PairGain WAN card, the 883060 and 883160 IP Router cards and other features and fixes. It supports all Server cards in existence at the time of this release. Please refer to the Product Bulletin for more details. Requires 880360 CPU and 892260, 892360 or 892460 Interface card.
60523 CPU Firmware, Host Version 5.2.3 Latest release supporting the 5.2 platform. In addition to supporting the functionality of the 5.1 platform, this release also supports the 831060 16 channel LBRV Server card and other features and fixes. It supports all Server cards in existence at the time of this release. Please refer to the Product Bulletin for more details. Requires 880360 CPU and 892260, 892360 or 892460 Interface card.
60532 CPU Firmware, Host Version 5.3.2 Latest release supporting the 5.3 platform. In addition to supporting the functionality of the 5.2 platform, this release also supports the 822460 and 822560 SRU cards. It supports all IMACS Server cards. Please refer to the Product Bulletin for more details. Requires 880360 CPU and 892260, 892360 or 892460 Interface card.
  IMACS WAN Cards | FOR SEARCH WITHIN THIS LIST USE YOUR BROWSER SEARCH FUNCTION (CTL F)
800060 WAN card, Single, T1/E1, CE Marked Stainless steel faceplate with ejector. Provides a single T1 or E1 interface. Requires one 81130 or 81230 plug-in module.
801060 WAN card, Dual T1/E1, CE Marked Stainless steel faceplate with ejector. Supports up to 2 T1 or E1 line interfaces. Can simultaneously support 1 T1 and 1 E1. Must have two Line Interface Modules installed for proper operation. May operate in CAS or CSS mode. Requires one 81130 or 81230 plug-in module per port.
801460 WAN card, Dual T1/E1 WAN card with Relays, CE Marked Stainless steel faceplate with ejector. Used with 880160, 880260 or 880360 Cross-Connect CPUs only. Provides 1:N redundancy for dual WAN cards when plugged into slot W4; acts as redundant mate for Dual WAN cards, 801060, located in slots W1, W2, W3. Plug-in modules on the redundant card must exactly match plug-modules of cards to be backed up. Requires the appropriate 81130 or 81230 plug-in module per port.
81130 WAN Module, Line Interface Module for DSX/CEPT Termination, GR-1089, CE Marked Used with 8000xx, 8010xx, 8014xx, and 8015xx WAN cards to provide DSX or E1 line interface. One 81130 is required for each DSX (external CSU required) or E1 port. Maximum 2 modules per WAN card. For E1 operation, module is manually jumpered to select either 75 Ohms or 120 Ohms termination. CE marked, NEBS compliant, and built to GR-1089 specification.
81230 WAN Module, Line Interface Module for CSU Termination, GR1089 Used with 8000xx, 8010xx, 8014xx, and 8015xx WAN cards to provide CSU line interface. Provides complete CSU functionality for T1 lines. One 81230 is required for each CSU port (maximum 2 per WAN card). NEBS compliant and built to GR-1089 specification.
   Voice Cards | FOR SEARCH WITHIN THIS LIST USE YOUR BROWSER SEARCH FUNCTION (CTL F)
810860 E&M/TO card, 8-Port, 2-Wire, CE Marked Stainless steel faceplate with ejector. Supports E&M types I, II, IV and V. Normal E&M, Transmission Only and E&MR2 modes are supported. May be used with 887160 ADPCM and 830060 and 831060 LBRV compression cards.
811960 E&M/TO card, 8-Port, 4-Wire, Extended Range, CE Marked Stainless steel faceplate with ejector. Supports E&M types I, II, IV and V. Normal E&M, Transmission Only and E&MR2 modes are supported. May be used with 887160 ADPCM and 830060 and 831060 LBRV compression cards. Extended TX TLP range is added to support dedicated 4-wire modem applications - especially important for data transmission speeds of 19.2Kbps or higher. CE Marked for TO mode only.
811961 E&M/TO card, 8-Port, 4-Wire, Extended Range, -24V, CE Marked Same as 811960 except it runs on a -24V system. Stainless steel faceplate with ejector. Supports E&M types I, II, IV and V. Normal E&M, Transmission Only and E&MR2 modes are supported. May be used with 887160 ADPCM and 830060 and 831060 LBRV compression cards. Extended TX TLP range is added to support dedicated 4-wire modem applications - especially important for data transmission speeds of 19.2Kbps or higher. CE Marked for TO mode only.
812960 FSX card, 8-Port, 2-Wire, 600 Ohm, Stainless Steel Faceplate Two wire interface, supporting signaling modes Foreign Exchange Station (connects to 2-way PBX trunk or key system), Foreign Exchange Software Defined Network (emulates E&M connection to class 4 switches). PLAR (point-to-point unswitched), DPO (1-way trunks from PBX, Key system or telephone) and SLC96 (Subscriber Loop Carrier 96). Type settings include variety of loop start and ground start options. Use with 600-Ohm termination facilities. Includes lower power setting for short loops. May be used with 887160 ADPCM and 830060 and 831060 LBRV compression cards. For use with all host s/w. Stainless steel faceplate with ejector.
813970 FXO card, 8-Port, 2-Wire, 600 Ohm, Stainless Steel Faceplate Two wire interface, supporting signaling modes Foreign Exchange Station (connects to 2-way PBX trunk or key system), Foreign Exchange Software Defined Network (emulates E&M connection to class 4 switches), DPT (1-way incoming trunks from PBX, Key system or telephone) and MRD (point-to-point unswitched). Signal settings include variety of loop start and ground start options plus R2. Use with 600-Ohm termination facilities. May be used with 8871xx ADPCM and 8300xx LBRV compression cards. Stainless steel faceplate with ejector. This version improves Ground Start mode when used with host 5.1.4 s/w only. Otherwise, can be used with all host s/w.
815060 FXO card, 8-Port, 2-Wire, 600 Ohm, Stainless Steel Faceplate, DTMF CID Similar to the 813960 and 813970 except that it is TBR21 compliant and supports CLIP (Calling Line Identification Presentation), a form of Caller ID. Except for MRD, all other states and modes of the 813960/70 are supported. Requires v4.2.4 CPU firmware and 880260 CPU. Not for use in USA. Stainless steel faceplate with ejector.
  IMACS Products - Data Cards | FOR SEARCH WITHIN THIS LIST USE YOUR BROWSER SEARCH FUNCTION (CTL F)
820260 HSU card, 2-Port, RS-530/V.35 Interface, CE Marked Two-Port High Speed Unit (HSU) for 56K, 64K and Nx56/64K data applications. Supports 2 RS530/RS449 or V.35 data ports. Can also support RS232 data through the use of 1253 personality module. DB25F connectors. Stainless steel faceplate with ejector. CE Marked.
820360 HSU card, 2-Port, V11 Interface, CE Marked Two-Port High Speed Unit (HSU) can be used to provide IMACS external main clock from a Nx56/64K port. V.11/RS530 or x.21 interfaces on DB25F connectors. Can connect as DCE or DTE. Also supports Nx56/64K external clock to IMACS. Stainless steel faceplates with ejector. Requires v4.2.0 or higher on 880260 CPU, or v5.x.y on 880360 CPU. CE Marked.
821260 HSU card, 2-Port, V.35 Interface Two-Port High Speed Unit (HSU) for 56K, 64K and Nx56/54K data applications. Provides true V.35 interface on DB25F connectors. Connects to A, B, C and D buses. Stainless steel faceplate with ejector.
821360 HSU card, 2-Port with RS-530/V.35, 2 Dial Ports with RS-366/V.25bis, CE Marked Two-Port High Speed Unit (HSU) for 56K, 64K and Nx56/64K data applications. Supports 2 RS530 or V.35 data ports; selection is made on a port-by-port basis using on-board switches. Supports V.25bis and/or RS-366 dialing for switched data applications when used with 884060 PRI Server card. RS-530 and "pseudo" V.35 interfaces on DB26F connectors. RS-366 on DB15 connector. Propriety in-band performance monitoring system. Stainless steel faceplate with ejector.
821460 HSU card, 2-Port, V.35 Interface, CE Marked Two-Port High Speed Unit (HSU) with V.35 interfaces on DB25F connectors. Ports may be configured for either trunk or user peripheral connection and connects as either DCE or DTE. Connects to A, B, C and D buses. Also supports Nx56/64K external clock to IMACS. Stainless steel faceplate with ejector. Requires v4.5.x or higher or v5.x.y or higher CPU firmware. CE Marked.
821570 HSU card, 4-Port, RS-530/V.35 Interface, CE Marked Four-Port High Speed Unit (HSU) for 56K, 64K and Nx56/64K data applications. The selection of RS530 or V.35 is made on a port-by-port basis using on-board switches. Can also support RS232 data at 56Kbps through the use of the 1253 Personality Module. Has four DB26F connectors. Has improved clock jitter performance. Stainless steel faceplate with ejector. CE Marked.
821660 HSU card, 4-Port, RS-530/V.35 Interface, CE Marked Four-Port High Speed Unit (HSU) for 56K, 64K and Nx56/64K data applications. The selection of RS530 or V.35 is made on a port-by-port basis using on-board switches. Can also support RS232 data at 56Kbps through the use of the 1253 Personality Module and 1240 cable adapter. Has four DB26F connectors. Supports tail circuits greater than 24 timeslots, V.35 interface compatible with international standards, and individually selectable transmit/receive clock inversion options. Stainless steel faceplates with ejector. Requires v3.8 or higher or v5.1 or higher CPU firmware. CE Marked.
822060 SRU card, 10-Port, RS-232C / V.24 Sync/Async Operation, CE Marked Ten-Port Sub Rate Unit with RJ-48 modular connectors. Supports synchronous and/or asynchronous data ports from 300 bps to 38.4Kbs. Supports DS0-A, DS0-B, V.14 and X.50 Division 3 subrate multiplexing formats. Connects to A and B buses only, limiting its operation to 62 ports. See Data Section in manual for aggregate input speed restrictions. SRU card ports can also be multiplexed with voice traffic on an ADPCM engine (up to 19.2 Kbps data circuit in 24 Kbps ADPCM channel). Stainless steel faceplate with ejector. CE Marked.
822061 SRU card, with Idle Pattern Feature Stainless Steel Faceplate, CE Marked Ten-Port Sub Rate Unit with RJ-48 modular connectors. Functionality equivalent to 822060 SRU card except Idle Pattern changed for OxFF to Mark for A, Hlink and ADPCM frames with INTF = Async. Uses V3.0 card FW. CE Marked.
822160 SRU card, C&D Bus, CE Marked Ten-Port Sub Rate Unit with RJ-48 modular connectors. Functionality equivalent to 822060 SRU card. Connects to the A, B, C and D buses. When used with 822060, increases the SRU port density per IMACS system beyond the current limit of 62 to a maximum of 80. Requires Cross Connect CPU 880160 or 880360. CE Marked.
822560 LD-SRU card, 10-Port, RS-232E, Sync/Async v.14 Operation Special Ten-Port Low Delay Sub Rate Unit (SRU) with RJ-48 modular connectors. Connects to the A, B, C and D buses. Supports synchronous and/or asynchronous data ports from 300 bps to 38.4Kbs. Supports DS0-A, DS0-B, V.14 and X.50 Division 32 subrate multiplexing formats by hardware instead software as in the 822060 SRU. The configuration is controlled via local terminal or remote NMS. The SRU offers lower delay, increasing throughput: Maximum of 3 ms +/- 10% end to end of rates 9.6 kbps or higher for sync. Maximum of 6 ms +/- 10% end to end of rates 9.6 kbps or higher for sync. SRU card ports can also be multiplexed with voice traffic on an ADPCM engine (up to 19.2 Kbps data circuit in 24 Kbps data circuit in 24 Kbps ADPCM channel). Supports CSU, DSU and CPU loopbacks. Requires v5.3, v3.9 or higher CPU firmware.
824160 OCU-DP card, 5-Port Five-Port Office Channel Unit-Data Port (OCU-DP) with RJ-48 modular connectors. Allows provisioning of DDS services or consolidation of DSU traffic as DS0-A or DS0-B. Interfaces directly to DSU at speeds up to and including 64Kbps. Does not support BCH error correction, performance monitoring or operation in CSU mode (used only for back-to-back OCU-DP ports). Emulates an 8247 for existing system compatibility. Each port may by connected to a DSU/CSU operating at 64, 56, Switched 56, 19.2, 9.6, 4.8 or 2.4Kbps. DSUs can be local to several thousand feet distant to IMACS based on speed and wire gauge. Stainless steel faceplate with ejector. Built to GR-1089 specification. Requires -48VDC.
824660 OCU-DP card, 10-Port, CE Marked Ten-Port Office Channel Unit-Data Port (OCU-DP) with RJ-48 modular connectors. Allows provisioning of DDS services or consolidation of DSU traffic as DS0-A or DS0-B. Interfaces directly to DSU at speeds up to and including 64Kbps. Does not support BCH error correction, performance monitoring or operation in CSU mode (used only for back-to-back OCU-DP ports). Emulates an 8247/845 combination for existing system compatibility. Each port may by connected to a DSU/CSU operating at 64, 56, Switched 56, 19.2, 9.6, 4.8 or 2.4Kbps DSUs can be local to several thousand feet distant to IMACS based on speed and wire gauge. Stainless steel faceplate with ejector. Built to GR-1089 specification. Requires -48VDC.
8249 OCU-DP card, 2-Port with Error Correction Two-Port Office Channel Unit-Data Port (OCU-DP) with RJ-48 modular connectors. Provides interface for provisioning of DDS services or consolidation of DSU traffic. Supports DS0-A or DS0-B sub-rate, 56K, 64K and Switched 56K DDS. Supports BCH error correction, performance monitoring or operation in CSU mode. Secondary channel operation can be enabled if desired. Optional error correction for inter-IMACS circuits. Requires DC main power supply or -48VDC converter.
825460 DS0-DP card, 4-Port Co/Contra-Directional Selectable, CE Marked Four-Port DS0-Data Port (DS0-DP) with DB-15F connectors. Provides 4 ports of DS0-DP or G.703 64 K. For G.703, clock can be selected to be co- or contra-directional. Stainless steel faceplate with ejector.
826070 BRI "U" card, 8-Port, 2-Wire, CE Marked Provides 8 ports of 2-wire 2BIQ interface via a single RJ27X(F) (50 pin Amp) connector. Adheres to 2B+D format. Supports external timing (in Host Release 3.6.x). Can be used to support NTUs for dedicated operation or for connection to BRI "U" interface devices. Commonly used for BRI Terminal Extension. Built to GR-1089 specification. Stainless steel faceplate with ejector. Remote NTU management only supported in V3.6.x or higher, v4.x.y or v5.x.y CPU firmware. CE Marked.
826171 BRI "U" card, 8-Port, 2-Wire, with Sealing Current, CE Marked Provides 8 ports of 2-wire 2BIQ interface via a single RJ27X(F) (50 pin Amp) connector. Adheres to 2B+D format. Supports external timing (in Host Release 3.6.x). Can be used to support NTUs for dedicated operation or for connection to BRI "U" interface devices. Commonly used for BRI Terminal Extension. Provides sealing (or wetting) current, 7.5mA or 15mA. No "DC Signature" feature.
826270 BRI "S/T" card, 8-Port, 4-Wire, GR-1089, CE Marked Provides 8 ports of 4-wire ISDN BRI S/T interface via a single RJ27X(F) (50 pin Amp) connector. Supports external timing. Adheres to 2B+D format. Provides TE, NT1 and NT2 emulation. Commonly used to provide remote extension of four-wire BRI CPE devices from an ISDN PBX. Requires external power connection (-48VDC) if more than 3 cards installed in IMACS chassis unless 891930 and 8908 are used. Stainless steel faceplate with ejector. Requires Host Release v3.6.x or higher, v4.2.x or v5.x.y CPU firmware. CE Marked.
828060 PM-IOR Router card, One-Port Inter Office Router user card based on Lucent Technologies PortMaster product line. Connects 10BaseT Ethernet LAN to T1/E1 WAN. Uses PPP or Frame Relay and IP (TCP/IP and IPX) to route up to 1.2 Mb/s through WAN. Can assign Nx56/64Kbps DS0s. Configure router through RJ-45 console port. Supports SNMP network management. Comes with complete PortMaster Router Command Reference Guide on CD and configuration cable. Requires v1.1.y, v3.8.y or v5.1.y or higher CPU firmware.
  Communications Server Cards | FOR SEARCH WITHIN THIS LIST USE YOUR BROWSER SEARCH FUNCTION (CTL F)
831060 Low Bit Rate Voice (LBRV) Server card, 16-Port, CE Marked Performs A-CLEP (G.729) voice compression. The LBRV card occupies a User card slot and takes voice traffic from either the WAN or User Bus. Supports 8 channels of voice in 1 DS0 and 16 in 2 DS0s. LBRV card output = 3 composite HDLC links at 64, 128 or 192 Kbps Links may be routed directly to WAN cards or the Frame Relay Server. Stainless steel faceplate with ejector. Requires 68100 LBRV firmware (must be ordered separately). Requires 5.2.x CPU firmware or above.
887160 ADPCM Server card, Supports 40, 32 or 24Kbps ADPCM, CE Marked The 887160 has 32 pairs of voice compression engines that will accept input directly from voice, SRU, BRI or WAN cards. The sum of compression rates for each engine must equal 64Kbps. Selectable compression rates include 40, 32 or 24Kbps with the latter not supporting DTMF, FAX or Modem tones (see data sheet for full specification). The 24Kbps option can transport SRU data up to 19.2Kbps. This model supports 1:1 or 1:2 redundancy. Maximum of 2 active 887160 ADPCM Servers (plus 1 redundant) per IMACS. If CPU load is 5.x, it can support 3 active ADPCM server cards. ADPCM coding to G.721/726 with transition signaling to ANSI T1.302 - 1989. Stainless steel faceplate with ejector. Requires v3.6.x or higher, v4.x.y or v5.x.y CPU firmware and cross connect CPU (880160, 880260, 880360).
  IMACS Advanced Communication Server Cards (ACS):
881160 Advanced Communications Server, Frame Relay, CE Marked 881160 ACS card with Frame Relay Firmware (62180 or 62220 ordered separately and shown below). Stainless Steel Faceplate with ejector. Requires v5.x.y CPU firmware.
881162 Advanced Communications Server, BRI/PRI , CE Marked 881160 ACS card with BRI/PRI Firmware (65130 ordered separately and shown below). Stainless Steel Faceplate. Requires v4.x or v5.x.y (recommended) CPU Firmware.
881360 Advanced Communications Server, MCC, 128 Remote Mgmt. Ports & 1 10 Base T , CE MarkedLocal Port The 881360 Management Channel Concentrator (MCC) card is comprised of the 881160 with additional expansion card (not available separately). Card is characterized through addition of 63xxx Server Firmware (must be ordered separately). This card allows the remote management of up to 128 IMACS systems via TCP/IP or SNMP. Stainless steel faceplate with ejector. Requires v4.2.x, v4.6.x or v5.x.y (recommended) CPU firmware.
883160 IP Router & Bridging Server card, 10 Base-T, CE Marked Provides IP Routing and Bridging functionality with 10 Base-T Ethernet port. Requires 67240 firmware ordered separately, which provides routing and bridging function using Frame Relay encapsulation (RFC 1490) over a maximum of 128 Frame Relay PVCs (3 physical ports), ARP, RIP, and Inverse ARP are used as routing protocols. Frame Relay output may be V.35, EIA-530, fractional T1/E1 or full T1/E1. Requires v5.1.0 or above CPU firmware. Recommended 5.2.1, 5.2.2, 5.2.3 or 5.3.2 F/W in order to use 128 static routes.
  IMACS Server Firmware | FOR SEARCH WITHIN THIS LIST USE YOUR BROWSER SEARCH FUNCTION (CTL F)
62180 FR Firmware, Frame Relay Server Firmware for ACS card. Version 1.8. Provides encapsulation FRAD function for SDLC/HDLC data and connection of frame relay circuits, with improved congestion management. All inputs to Frame Relay Server must be at 56, 64 or Nx56/64K data rates. Input ports may be V.35, EIA-530, DDS 56/64K, 2B1Q, fractional T1/E1 or time slot from 8231xx FRAD card. Concentrated outputs may be V.35, EIA-530 or Fractional T1/E1. Requires 881160 FRS card (Must be ordered separately). Requires v5.0.0 CPU firmware or higher.
62230 FR Firmware, Frame Relay Server Firmware w/QoS for ACS card. Version 2.3. Provides encapsulation FRAD function for SDLC/HDLC data and connection of frame relay circuits with 4 levels of priority to allow voice over Frame Relay. All inputs to Frame Relay Server must be at 56, 64 or Nx56/64K data rates. Input ports may be V.35, EIA-530, DDS 56/64K, 2BIQ, fractional T1/E1 or time slot from 8231xx FRAD. Concentrated outputs may be V.35, EIA-530 or Fractional T1/E1. Requires 881160 FRS Card (Must be ordered separately.) Requires v.5.2.0 CPU firmware or higher.
63130 MCC Firmware, Mgmt. Comm. Concentrator Firmware for ACS card. Version 1.3. Allows up to 128 IP management channels to be concentrated onto a single Ethernet link, providing the means to manage a large network of IMACS products from a single location using IP techniques. Provides IP connectivity to up to 128 remote IMACS units. Local connectivity to the MCC is provided through the on-board 10BaseT Ethernet connector. Latest release of MCC Firmware.
65130 BRI/PRI Firmware, ISDN BRI to PRI Server Firmware for ACS card. Version 1.3. Provides inter-working between NET3 based BRI and NET5 based PRI. Fixed timeslot mapping only in this release. Uses standard 8260xx or 8261xx based BRI card for BRI interface. PRI software is provided by 65130; an 884060 based PRI Server card is not required. Additional information is available in the 4.4.0 Product Release Abstract. Requires 881162 BRI/PRI Server card. Requires v4.4.x or v5.x.y (recommended) CPU firmware.
67240 IP Routing and Bridging Firmware, Internet Protocol Firmware for ACS card. Version 2.4. Provides routing and bridging of Ethernet IP traffic using Frame Relay encapsulation (RFC 1490) over a maximum of 128 Frame Relay PVCs (3 physical ports). ARP, RIP, and Inverse ARP are used as routing protocols. Frame Relay output may be V.35, EIA-530, fractional T1/E1 or full T1/E1. Requires 883060 or 883160 IP Router card. Requires v5.1.0 or higher CPU firmware. Recommended 5.2.1, 5.2.2, 5.2.3 or 5.3.2 F/W in order to use 128 static routes.
68100 LBRV Voice Compression Firmware for DSP card, 16-Port. Version 1.0. Required for each DSP card used as LBRV compression card. Each DSP card with 68100 firmware will perform voice compression to 7.3 Kbps (similar to G.729) for up to 16 channels of PCM voice originating on WAN card time slots or analog voice cards over 2 DS0s. Supports fax recognition and trunk conditioning. Requires 831060 DSP card (must be ordered separately). Requires v5.2.x CPU or higher.
  IMACS Products - Alarms | FOR SEARCH WITHIN THIS LIST USE YOUR BROWSER SEARCH FUNCTION (CTL F)
840160 External Alarms card, 4-Port, 4 Inputs & 4 Outputs, CE Marked Supports four outbound switches and four inbound sensors. The outbound switches are used to report internal alarms to external devices by triggering form-C contract closures (on Major or Minor alarms). Triggering may be an opening or closure of the contact. The inbound sensors are used to bring foreign indications into the system. External alarms reported by a sensor are listed in the IMACS alarm history file. Stainless steel faceplate with ejector. Requires -48VDC power source within IMACS (8902, or 8901 with 8903 or 8905 voltage converter).
840260 External Alarms card, 3-Port plus Power Failure Alarm, CE Marked Supports 3 outbound and 3 inbound sensors. card performance is identical to the 8401 External Alarm card, except that the fourth alarm port on the 840260 can only be used as an outbound alarm to show if the system power fails. Stainless steel faceplate with ejector. Requires -48VDC power source within IMACS (8902, or 8901 with 8903 or 8905 voltage converter).
  Network Management Software - OnLine EMS Software
600100 OnLine 1.2 Software IMACS and StreamLine element management system based on HP OpenView Network Node Manager on Sun Solaris. Sun Workstation, Sun Solaris, and HP OpenView are not included and must be obtained separately. This software package is bundled with one of the License Options (Class 1-5 Software Packages) products (70001 to 70006) listed below. Must order one of the license packages below to get the OnLine 1.2 software. In addition, any system can be upgraded to more operators and nodes with one of the License Upgrade Packages below.
Equipment needed for OnLine 1.2: Sun workstation Ultra 5 or Ultra 10 with Sun Operating System (Solaris 2.51 or 2.6 with TCP/IP installed and configured) and with a minimum of 256 Mbytes memory and 2 Gbytes disk space; HP Open View 5.0.
70000 Evaluation Package (License Option) For unlimited evaluation use only. Manages 2 nodes of IMACS and/or StreamLine, and supports 2 operators. Bundled with 600100.
70006 Class E Software Package (License Option) Manages up to 50 nodes of IMACS and/or StreamLine, and supports up to 2 operators. Bundled with 600100.
70001 Class 1 Software Package (License Option) Manages up to 100 nodes of IMACS and/or StreamLine, and supports up to 4 operators. Bundled with 600100.
70002 Class 2 Software Package (License Option) Manages up to 200 nodes of IMACS and/or StreamLine, and supports up to 8 operators. Bundled with 600100.
70003 Class 3 Software Package (License Option) Manages up to 300 nodes of IMACS and/or StreamLine, and supports up to 12 operators. Bundled with 600100.
70004 Class 4 Software Package (License Option) Manages up to 400 nodes of IMACS and/or StreamLine, and supports up to 16 operators. Bundled with 600100.
70005 Class 5 Software Package (License Option) Manages up to 500 nodes of IMACS and/or StreamLine, and supports up to 20 operators. Bundled with 600100.
70061 License Upgrade Package E-1 (License Upgrade Option) Upgrade an existing OnLine 1.2 system from Class E to Class 1. Original serial number required as license verification with purchase order. Follow instructions in OnLine License Guide.
70062 License Upgrade Package E-2 (License Upgrade Option) Upgrade an existing OnLine 1.2 system from Class E to Class 2. Original serial number required as license verification with purchase order. Follow instructions in OnLine License Guide.
70063 License Upgrade Package E-3 (License Upgrade Option) Upgrade an existing OnLine 1.2 system from Class E to Class 3.Original serial number required as license verification with purchase order. Follow instructions in OnLine License Guide.
70064 License Upgrade Package E-4 (License Upgrade Option) Upgrade an existing OnLine 1.2 system from Class E to Class 4. Original serial number required as license verification with purchase order. Follow instructions in OnLine License Guide.
70065 License Upgrade Package E-5 (License Upgrade Option) Upgrade an existing OnLine 1.2 system from Class E to Class 5. Original serial number required as license verification with purchase order. Follow instructions in OnLine License Guide.
70012 License Upgrade Package 1-2 (License Upgrade Option) Upgrade an existing OnLine 1.2 system from Class 1 to Class 2. Original serial number required as license verification with purchase order. Follow instructions in OnLine License Guide.
70013 License Upgrade Package 1-3 (License Upgrade Option) Upgrade an existing OnLine 1.2 system from Class 1 to Class 3. Original serial number required as license verification with purchase order. Follow instructions in OnLine License Guide.
70014 License Upgrade Package 1-4 (License Upgrade Option) Upgrade an existing OnLine 1.2 system from Class 1 to Class 4. Original serial number required as license verification with purchase order. Follow instructions in OnLine License Guide.
70015 License Upgrade Package 1-5 (License Upgrade Option) Upgrade an existing OnLine 1.2 system from Class 1 to Class 5. Original serial number required as license verification with purchase order. Follow instructions in OnLine License Guide.
70023 License Upgrade Package 2-3 (License Upgrade Option) Upgrade an existing OnLine 1.2 system from Class 2 to Class 3. Original serial number required as license verification with purchase order. Follow instructions in OnLine License Guide.
70024 License Upgrade Package 2-4 (License Upgrade Option) Upgrade an existing OnLine 1.2 system from Class 2 to Class 4. Original serial number required as license verification with purchase order. Follow instructions in OnLine License Guide.
70025 License Upgrade Package 2-5 (License Upgrade Option) Upgrade an existing OnLine 1.2 system from Class 2 to Class 5. Original serial number required as license verification with purchase order. Follow instructions in OnLine License Guide.
70034 License Upgrade Package 3-4 (License Upgrade Option) Upgrade an existing OnLine 1.2 system from Class 3 to Class 4. Original serial number required as license verification with purchase order. Follow instructions in OnLine License Guide.
70035 License Upgrade Package 3-5 (License Upgrade Option) Upgrade an existing OnLine 1.2 system from Class 3 to Class 5. Original serial number required as license verification with purchase order. Follow instructions in OnLine License Guide.
70045 License Upgrade Package 4-5 (License Upgrade Option) Upgrade an existing OnLine 1.2 system from Class 4 to Class 5. Original serial number required as license verification with purchase order. Follow instructions in OnLine License Guide.
  Network Management Software - EMS Software:
70100-1 EMS, v4.1.2, User License Package Package of 5 user licenses required for 5 simultaneous users of EMS v4.1.2. Requires 70105-04 EMS Complete Software. Sales limited to networks that only use modems for remote access to IMACS. Compatibility limited to IMACS host release 3.4.4 and below.
70105-04 EMS Complete, v4.1.2, for SUN Solaris 2.x for x86 and SPARC Package of EMS complete software with 5 user licenses. Sales to be limited to networks that only use modems for remote access to IMACS. Compatibility limited to IMACS host release 3.4.4 and below. This package does not include work station and operating system.
  Network Management Software - Manuals
600170 OnLine 1.2 Installation and Administration Guide Additional manual for OnLine 1.2. Contact Order Fulfillment for availability.
600171 OnLine 1.2 Operator Guide Additional 1.2 Operator Guide. Contact Order Fulfillment for availability.
  Miscellaneous Equipment | FOR SEARCH WITHIN THIS LIST USE YOUR BROWSER SEARCH FUNCTION (CTL F)
Miscellaneous - Cables and Accessories -
1114F Cable, 5-ft., RJ48(M) to DB25(F) Straight-Thru This cable is used to connect RS232 DTE to the 822060 SRU card.
1114M Cable, 5-ft. RJ48(M) to DB25(M) Straight-Thru This cable is used to connect RS232 DTE to the 822060 SRU card.
1181 Connector Block, T1 Distribution Panel, 50-Pin Amphenol (F) to 8 xRJ48(F) The 1181 is used to connect up to 8 T1s to the 8920xx, 8921xx, 8922xx, 8923xx Interface card. Consult the IMACS Cable and Equipment Guide for more details.
118320 Connector Block, E1 Dist. Panel, 50-Pin, CE Marked The 118320 provides 8 pairs of BNC(F) connectors for connecting up to 8 E1 trunks to an 8920xx, 8921xx, 8922xx, 8923xx Interface card. Includes 50-pin (M) to (M) Amp cable and is suitable for 891630 IMACS 600 chassis only. Mounts in place of PS cover panel. Includes switch-selectable grounding options.
1184 Connector Block, E1 Distr. Panel, 50-Pin Amphenol (F), CE Marked The 1184 provides 8 pairs of BNC(F) connectors for connecting up to 8 E1 trunks to an 8920xx, 8921xx, 8922xx, 8923xx Interface card. Includes 50-pin (M) to (M) Amp cable and is suitable for 891830 IMACS 800 chassis only. Mounts in place of PS cover panel. Includes switch-selectable grounding options.
1203F Cable, 5-ft DB25(M) to M34(F) Straight-Thru V.35 The 1203F cable is used to connect V.35 DTE to HSU cards.
1203X Cable, 5-ft DB25(M) to M34(M) Cross-Over v.35 The 1203X cable is used to connect V.35 DCE to HSU cards.
1208 Cable, 6-ft 3 Amphenol (M) to 1 Amphenol (M) The 1208 cable is used to connect 3 FXS or FXO cards to one M66 block or other terminal wiring.
1210 Cable, 5-ft 1 Amphenol (M) to 1 Amphenol (M) Extension The 1210 cable is used to connect user cards with Amphenol connectors to M66 blocks or other terminal wiring.
1210 Cable, 5-ft 1 Amphenol (M) to 1 Amphenol (M) Extension The 1210 cable is used to connect cards with Amphenol connectors to M66 blocks or other terminal wiring.
1210SH Cable, Shielded, 5-ft 1 Amphenol (M) to 1 Amphenol (M) Extension The 1210 SH cable is used to connect cards with Amphenol connectors to M66 blocks or other terminal wiring where a shielded cable is required.
1215X Cable, 5-ft RJ48 (M) to DB15 (F) Cross-Over The 1215X cable is used to connect PBX equipment to the Interface card.
1216F Cable, 15-ft RJ48 (M) to DB25 (F) Straight-Thru The 1216F cable is used to connect a VT-100 terminal to the Interface card.
1216M Cable, 15-ft RJ48 (M) to DB25 (M) Straight-Thru The 1216M cable is used to connect a VT-100 terminal to the Interface card.
1219F Cable, 5-ft RJ48 (M) to DB9 (F) Straight-Thru The 1219F cable is used to connect a VT-100 terminal to the Interface card.
1231 Cable, 25-ft RJ48 (M) to RJ48 (M) Shielded The 1231 cable is used to connect terminal interface devices to the Interface card.
1239 Cable, RJ48 (F) to 2 x RJ48 (M), Y Adapter with two 1230 Cables Attached Used to support WAN card redundancy. RJ48(F) to 2 x RJ48(M). Y Adapter with two 1230 cables attached.
1253 Converter, RS-530 to RS-232 Personality Module Used to allow RS232 signals to be transmitted through HSU ports designed for RS530 signals.
1257 Gender Changer,V.35 M34 (F) to M34 (F) The 1257 is used to change the gender of V.35 cables from male to female.
1263F Cable, 5-ft DB26 (M) to M34 (F) Straight-Thru Used to connect V.35 DTE to the 8215 based HSU card.
1263M Cable, 5-ft DB26 (M) to M34 (M) Straight-Thru Used to connect V.35 DTE to the 8215 based HSU card.
1263X Cable, 5-ft DB26 (M) to M34 (M) Cross-Over Used to connect V.35 DCE to the 8215 based HSU card.
1264F Cable, 5-ft DB26 (M) to DB25 (F) Straight-Thru RS530 Used to connect RS530 or RS232 DTE to the 8215 HSU card.
1504 M66 Terminal Block, 2 Female 50-Pin Amp/Champ Connectors Allows the user to connect facilities with Amphenol connectors.
200100 Rack Mounting Hardware Kit Replacement rack mounting brackets and hardware for IMACS and StreamLine chassis.
200103 Filler Panel, Chassis Stainless Steel blank filler panel for IMACS or StreamLine chassis.
  Miscellaneous - Reference Guides | FOR SEARCH WITHIN THIS LIST USE YOUR BROWSER SEARCH FUNCTION (CTL F)
1918 IMACS Reference Guide, Version 3.4. Hard copy binder. Manual provides system and card configuration documentation for IMACS Host Release 3.4.x.
1930 IMACS Reference Guide, Version 4.2. Hard copy binder. Manual provides system and card configuration documentation for IMACS Host Release 4.2.x.
2001-SC IMACS Reference Guides, Versions 5.0, 5.1, 5.1.4, 5.2 and 5.3 on CD-ROM. CD-ROM contains system and card configuration documentation for all IMACS Host Releases, 5.0, 5.1, 5.1.4, 5.1.5, 5.2 and 5.3. Soft copy only in Adobe PDF format. Includes IMACS cable guide, datasheets and product information book.
2002-SC IMACS Reference Guide, Version 4.1.2 on CD-ROM. CD-ROM contains system and card configuration documentation for IMACS Host Release 4.1.2. Soft copy only in Adobe PDF format. Includes IMACS cable guide, datasheets and product information book.
2003-SC IMACS Reference Guides, Versions 3.6, 3.7, 3.8 and 3.9 on CD-ROM. CD-ROM contains system and card configuration documentation for IMACS Host Releases, 3.6, 3.7, 3.8 and 3.9. Soft copy only in Adobe PDF format. Includes IMACS cable guide, datasheets and product information book.
2004-SC StreamLine Reference Guides, All 1.x Versions on CD-ROM. CD-ROM contains system and card configuration documentation for all StreamLine Host Releases, 1.0, 1.1 and 1.2. Soft copy only in Adobe PDF format. Includes cable guide and product information book.
2007-SC IMACS Reference Guide, CD-ROM contains complete documentation for IMACS PM-IOR Card (828060), including installation, configuration and operation. Contains complete PortMaster Router Command Reference Guide. Soft copy only in Adobe PDF format.
PM-IOR Card (828060).
  Miscellaneous - Network Termination Units
2200E Single Port V.35/V.36 Network Termination Unit Single port device provides full duplex transmission at data rates up to 128 Kb/s over two wire unconditioned lines. 2B1Q encoding. Operating range up to 5.2 Km. May be remotely manage with IMACS BRI "U" card (826070 or 826171.) Synch 1.2 to 128 Kb/s. Asynch 300 bps to 38.4 Kb/s. Requires BRI "U" card and host code 3.6 or above, 4.2, or 5.x.
2290E NTU Power Pack, 110V 110V power pack, power cable not included.
2291E NTU Power Pack, 240V 240V power pack, power cable not included.
Sign up for Our Email Newsletter
Email:  
For Email Marketing you can trust

TRANSLATE THIS WEBSITE
INTO YOUR PREFERRED LANGUAGE
worldglobe

 Home | Products | Order | About Us | Contact | Search

DataComSource.com - All products, logo's and brand names mentioned are trademarks or registered trademarks of their respective owners.